Get 'er Dun!

So about 2 or 3 weeks ago, we decided to start restoring the Hasty Baker oven I bought over a year ago. Tarps were brought out and laid down, tools were assembled and deconstruction began. In the middle of my living room floor.

All was well and good until we hit a snafu. We both got kind of tired of working on it. So, this morning, I decided enough was enough. Today was the day. Carpe Diem and all that stuff. Going to get this project done! So I made a list, and put "stove" at the top of it. I put a bunch of other stuff there too, not humanly possible to get it all done in one weekend, but you have to at least try.

One of the other "things" on my list was to get as much laundry done as possible, being as how it's going to rain tomorrow. As much as possible is 3 loads which is all the outside lines will hold and the one every other week load that goes in the dryer.

There was lots of other stuff, but these two were enough to concentrate on.

A couple of different sized screwdrivers were needed as well as needle nose pliers and crescent wrenches. Some of the screws were obstinant, to say the least. No problem. Go get the cordless screwdriver/drill. Hunt up some drill bits and 3 hours later, all screws have been either removed forcibly or otherwise and we have lots of pieces. Still in the middle of the living room floor.

Since before my owning this stove, it belonged to a rather large family of mice, a good washing was required of all of the pieces and parts. I'm not going to lie, the smaller, more greasy parts went in the dishwasher, and I don't even wanna hear about how I can justify using the dishwasher when I'm hanging clothes outside, in January, in N. Michigan. I can, I just can!

So while the smaller parts are in the dishwasher, I'll continue to wash up the remaining larger pieces and parts and put them over by the woodstove to dry. Next step - sandblasting to remove rust, maggot juice, and everything else that the washings didn't get rid of. Wouldn't it be nice if the next things to do were simply to paint it and put it back together?

The paint part I can handle, the putting it back together, well, that might get dicey. However, I am, in possession of the most skilled hubby on the planet when it comes to reconstructing my disasters. And I did take pictures, of various pieces and parts coming apart. Lots of them, so when it's time, with any amount of luck at all, this might happen.

The downside? This is only 1/3 of the whole project. The upper, warming ovens and ledge. Still out on the front porch, but definitely on(the) deck is the oven/range part of this project. Then the bottom part that the whole she-bang sits on.

After washing up all of this stuff, I should probably go get the clothes off the line, as the weather people have opted to lie once more and instead of raining tomorrow, it is starting to mist a bit. The air is heavy, and the temps are hovering around 33. Not a good situation, as when the rain/mist, that will lead into snow hits the frozen roads, yeah, instant ice! Fun!!

As for knitting... so much for my "Project Monogamy"! Whils't in Colorado, I found some extremely pretty yarn - it was definitely a must have!, and promptly started turning it into some nice, dressier than normal, fingerless mitts to wear with my nice leather jacket. Those aren't done yet. There's the throw-it-on-to-run-outside-quick shawl in alpaca and wool that isn't done yet. There's a baby sweater, that's almost done (on my list for things to do today), there's a few other sweaters that I'm fiddling with as they don't have a pattern, just kind of winging it, another pair of fingerless mitts in some new yarn that I'm reviewing, and enough socks to feed a small army. Yes, I did just say that. I'm sure there's a few other things I'm not thinking of right now.

Back to the mice dropping, maggot infested pieces and parts that need to be washed! And where, might you ask, is hubby while I'm doing all of this deconstructing? As usual he stays clear of my disasters until I fly the white flag, but this time, he went in search of new tips for his sandblaster! YAY!! It's really gonna get done!!!